Offshoreonly.com - Search Results

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: tms1155
Showing results 1 to 25 of 128
Search took 0.01 seconds.
12-22-2010, 06:23 PM
Replies: 18
Views: 2,352
Posted By tms1155

I dont think you can put 454's in without doing...

I dont think you can put 454's in without doing transom over and possibly stringers too. If I remember correctly there was no more than an inch or two between the 350's. The alpha transom housings...
06-05-2010, 08:54 PM
Replies: 15
Views: 2,449
Posted By tms1155

you would only get voltage if you turn the key to...

you would only get voltage if you turn the key to start. jump those 2 wires together and try to start. If it starts switch is bad.(if you cut them jump the two going to engine, not controls)
Forum: Baja
05-27-2010, 09:28 PM
Replies: 3
Views: 835
Posted By tms1155

When it comes to boats nothing is normal. Could...

When it comes to boats nothing is normal. Could have come from factory or been changed along the way. Sometimes people want to be able to use trim without turning on switches when trailering boat.
Forum: Baja
05-26-2010, 09:32 PM
Replies: 3
Views: 835
Posted By tms1155

Sounds like trim pump pos. wire is hooked to...

Sounds like trim pump pos. wire is hooked to batt #2. If it is remove it and put it to common lug on batt switch and it will work on either batt.
Forum: General Q & A
05-25-2010, 09:21 PM
Replies: 20
Views: 3,469
Posted By tms1155

The solonoids have nothing to do with power going...

The solonoids have nothing to do with power going to key switch. If the slave solonoid has power to one side, jump from that post to the small yellow one and engine should crank (You should only have...
05-13-2010, 11:33 PM
Replies: 13
Views: 4,716
Posted By tms1155

Driveshaft will not pull out with engine, it will...

Driveshaft will not pull out with engine, it will not pass gimbal bearing.
05-13-2010, 09:35 PM
Replies: 12
Views: 1,510
Posted By tms1155

Have them show you how to do it! They make it...

Have them show you how to do it! They make it with 3 big o/b's to fish offshore and props should never leave the water? I would guess you should only run one engine when you hit 1 to 2 foot seas.
05-11-2010, 10:03 PM
Replies: 13
Views: 4,716
Posted By tms1155

Gimbal bearing or u-joints for the growling noise...

Gimbal bearing or u-joints for the growling noise but neither of those will give you smoke. burnt smell and smoke is the coupler.engine may be out of alignment causing all of above.
05-08-2010, 07:53 PM
Replies: 6
Views: 1,291
Posted By tms1155

If you mean docking lights you will need all new...

If you mean docking lights you will need all new wires. the ones already in dash panel are not heavy enough to carry the power for those lights. Depending on how long the wires will be, you will need...
Forum: General Q & A
04-24-2010, 02:02 AM
Replies: 4
Views: 4,855
Posted By tms1155

same motor. They were just called 400 cyclones

same motor. They were just called 400 cyclones
03-12-2010, 11:27 PM
Replies: 23
Views: 3,241
Posted By tms1155

When you get them just hook the GPS up in a...

When you get them just hook the GPS up in a rubber raft and take them out about 100 miles and see if it will get them back. (run wires thru the sides of the raft)
03-02-2010, 11:13 AM
Replies: 10
Views: 1,326
Posted By tms1155

I didn't think they would send a letter, only a...

I didn't think they would send a letter, only a "MESSAGE"
02-25-2010, 08:28 PM
Replies: 9
Views: 1,205
Posted By tms1155

E-mail sent. I just looked on west marine and the...

E-mail sent. I just looked on west marine and the o/b setup is rated for 300HP single eng.and600HP dual eng
02-24-2010, 03:35 PM
Replies: 9
Views: 1,205
Posted By tms1155

You need to follow the instructions to bleed it...

You need to follow the instructions to bleed it right. I have a copy of them but cant post them. PM me your email and I will send it to you.
They make systems for O/B, I/O and straight inboards.
Forum: General Q & A
01-17-2010, 04:00 PM
Replies: 2
Views: 559
Posted By tms1155

I had the same problem with mine. I ran two #10...

I had the same problem with mine. I ran two #10 wires (pos & neg) direct from batt. and it solved it. (put fuse on pos. at batt.)
01-10-2010, 06:28 PM
Replies: 38
Views: 13,295
Posted By tms1155

If you have oval port heads now they are 330HP....

If you have oval port heads now they are 330HP. If they are rect. they are 370 or 400.
Forum: General Q & A
01-10-2010, 06:21 PM
Replies: 5
Views: 2,927
Posted By tms1155

Yes, just the red and black will make it work....

Yes, just the red and black will make it work. all the others are for linking unit to other electronics,(VHF Auto pilot, Radar Ets.) Just tape them back and forget them.
If your unit has internal...
01-07-2010, 10:39 PM
Replies: 20
Views: 2,762
Posted By tms1155

thats the one! Anybody that ever touched one...

thats the one! Anybody that ever touched one remembers it. Worst design in boating history!!!!!!!!!!!!!!
01-07-2010, 05:52 PM
Replies: 20
Views: 2,762
Posted By tms1155

They did use the same gear oil.

They did use the same gear oil.
01-06-2010, 02:07 PM
Replies: 20
Views: 2,762
Posted By tms1155

Thats what it is. No doubt about it.

Thats what it is. No doubt about it.
01-02-2010, 05:58 PM
Replies: 18
Views: 1,323
Posted By tms1155

That works too!

That works too!
01-02-2010, 02:42 PM
Replies: 18
Views: 1,323
Posted By tms1155

You need to smooth out those rough edges on the...

You need to smooth out those rough edges on the vent so the oil comes out smoothly and you dont cut your fingers.
Forum: General Q & A
01-01-2010, 04:33 PM
Replies: 13
Views: 1,363
Posted By tms1155

While your in there get rid of those wire...

While your in there get rid of those wire connectors and use heat shrink connectors. Those will corrode and cause problems.
12-15-2009, 07:26 PM
Replies: 4
Views: 1,964
Posted By tms1155

Other four in hospital or worse?

Other four in hospital or worse?
12-11-2009, 02:18 PM
Replies: 24
Views: 2,537
Posted By tms1155

Not sure about these rocker shafts, i'ts been a...

Not sure about these rocker shafts, i'ts been a while since I've done any HP engines. The original Merc 400 rockers had a flat side and a round side on the shaft. Had a customer put his back...
Showing results 1 to 25 of 128
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.