Offshoreonly.com - Search Results
Offshoreonly.com

Go Back  Offshoreonly.com > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 13
1
2
3
11
Last »
Search: Posts Made By: Tahoe540
Showing results 1 to 25 of 309
Search took 0.02 seconds.
Forum: General Q & A
12-27-2023, 09:16 AM
Replies: 5
Views: 376
Posted By Tahoe540

I have the 11 quart Champ pan on both my Gen V...

I have the 11 quart Champ pan on both my Gen V and Mark IV motors and really like them. They have good oil control. I cannot confirm the dipstick....
Forum: Do It Yourself, Boating on a Budget
12-15-2023, 08:28 AM
Replies: 32
Views: 3,000
Posted By Tahoe540

I ended up getting a custom set of Ross pistons,...

I ended up getting a custom set of Ross pistons, to get me 10.5:1. Went with a 4.600 bore because lack of ring pack choices at 4.580.

The pin is below the oil ring groove and has a .043 .043 3mm...
Forum: Do It Yourself, Boating on a Budget
12-11-2023, 08:59 AM
Replies: 32
Views: 3,000
Posted By Tahoe540

I completely agree with you. I got into boats...

I completely agree with you. I got into boats after drag racing and piston design I have found to be an important part of the differences. I do not like the short skirt in my marine motors for the...
Forum: Do It Yourself, Boating on a Budget
12-10-2023, 07:32 AM
Replies: 32
Views: 3,000
Posted By Tahoe540

Thanks for sharing your experiences. I will be...

Thanks for sharing your experiences. I will be trying swain or line to line on this next set of pistons.



I have used Icon's a few times and have no issues with the piston itself, and they are...
Forum: Do It Yourself, Boating on a Budget
12-08-2023, 09:55 AM
Replies: 32
Views: 3,000
Posted By Tahoe540

Pistons and coatings

I need to rebuild the bottom end of my 555 and considering the Mahle Powerpak set. I do like the smaller ring pack.
...
Forum: General Q & A
11-12-2023, 07:58 AM
Replies: 12
Views: 1,190
Posted By Tahoe540

I have run solid lifters on a hydraulic roller...

I have run solid lifters on a hydraulic roller for a season. I played around with lash from around .004-.008 just to get it as quiet as possible. Replaced solids with some Johnson hydraulic's last...
Forum: General Q & A
10-16-2023, 08:30 AM
Replies: 11
Views: 1,614
Posted By Tahoe540

I am running the 525 EFI cam in my 555 with...

I am running the 525 EFI cam in my 555 with bigger BB2 heads and more compression but I chose this cam because I have restrictive exhaust and it runs pretty good. Definitely not a cam for huge...
Forum: Vendor Talk
09-08-2023, 08:21 AM
Replies: 18
Views: 4,663
Posted By Tahoe540

Summit Racing has been selling Eddie Marine...

Summit Racing has been selling Eddie Marine products. I have bought many parts that they have in stock surprisingly.
Forum: Do It Yourself, Boating on a Budget
08-15-2023, 11:14 AM
Replies: 18
Views: 2,056
Posted By Tahoe540

I have used them on my wet exhaust. Summit has a...

I have used them on my wet exhaust. Summit has a great selection. ...
Forum: General Q & A
05-24-2023, 08:49 AM
Replies: 18
Views: 2,171
Posted By Tahoe540

I did a similar build in 2017 but was a 548 with...

I did a similar build in 2017 but was a 548 with 088 heads that had minor bowl and intake work done. The cam was a little bigger than a 741 but not much. Motor had around 10:25 compression as I...
Forum: General Q & A
10-24-2022, 09:10 AM
Replies: 6
Views: 1,031
Posted By Tahoe540

I have the LSM one and it is expensive but it...

I have the LSM one and it is expensive but it does work good. Doing springs is a pain in the ass with the heads on so a good tool does help with frustration. You could probably sell it after you...
Forum: General Q & A
05-14-2022, 01:35 PM
Replies: 15
Views: 1,821
Posted By Tahoe540

I have used rear sump oil pans before but they...

I have used rear sump oil pans before but they had kickouts on both sides and baffles. I recently used this pan on my BBC and was pretty happy with it even though it is a cheaper pan.
...
Forum: Do It Yourself, Boating on a Budget
04-15-2022, 08:37 AM
Replies: 10
Views: 2,270
Posted By Tahoe540

I just installed the Comp cam in my 496 build. ...

I just installed the Comp cam in my 496 build. Was the closest I could find to the 741. I was surprised Summit had 5 of these in stock too. They don't have any heads though.
...
Forum: General Q & A
01-14-2022, 08:59 AM
Replies: 57
Views: 15,000
Posted By Tahoe540

I have been building large cubic inch BBC motors...

I have been building large cubic inch BBC motors for about 15 years now starting with drag racing and moving into offshore boats. From a drag racing perspective you are looking for large flow...
Forum: Do It Yourself, Boating on a Budget
01-13-2022, 08:47 AM
Replies: 24
Views: 5,731
Posted By Tahoe540

Engine parts can be hard to get right now. I buy...

Engine parts can be hard to get right now. I buy a lot of parts through summit and most heads and other higher end parts are months out right now. I am building a 496 and have had to use other...
Forum: General Q & A
09-15-2021, 08:48 AM
Replies: 2
Views: 899
Posted By Tahoe540

I would just call and ask them.

I would just call and ask them.
Forum: Do It Yourself, Boating on a Budget
05-11-2021, 07:44 AM
Replies: 15
Views: 3,725
Posted By Tahoe540

I have heard of pouring diesel into the crankcase...

I have heard of pouring diesel into the crankcase to wash down any contaminants that may be in the motor but not start it. Just drain it. I would run it with cheap oil and drain it after a few...
Forum: General Q & A
03-11-2021, 08:40 AM
Replies: 42
Views: 7,215
Posted By Tahoe540

I just installed a new Bullett cam that I...

I just installed a new Bullett cam that I couldn't get the numbers to match the cam card.

I ended up installing it 6 degrees advanced and it finally matched. I called Bullett and the tech said...
Forum: General Q & A
02-06-2021, 08:35 PM
Replies: 27
Views: 9,876
Posted By Tahoe540

I did measure at .020 and was the same. I did...

I did measure at .020 and was the same. I did read about the asymmetrical lobes.

This motor now has BB2xtra CNC heads with Jesel shaft rockers. It also has a matching brodix intake.

I also...
Forum: General Q & A
02-03-2021, 07:52 AM
Replies: 27
Views: 9,876
Posted By Tahoe540

I just installed a hydraulic roller Bullet custom...

I just installed a hydraulic roller Bullet custom grind. They were really nice and quick to get me my new specs. My only issue was I had to install it 6 degrees advanced to match the cam card and...
Forum: Swap Shop
01-14-2021, 11:45 AM
Replies: 3
Views: 680
Posted By Tahoe540

I am not sure on the Teague blower pulley bolt...

I am not sure on the Teague blower pulley bolt pattern. It does fit standard 3 bolt balancer
Forum: Swap Shop
01-13-2021, 08:33 AM
Replies: 3
Views: 680
Posted By Tahoe540

Blower accessory pulley 3 groove

Been sitting on my shelf. Went NA so don't need this. $100 plus shipping....
Forum: Swap Shop
01-07-2021, 07:34 AM
Replies: 16
Views: 2,351
Posted By Tahoe540

Would you split your cam and valve train setup? ...

Would you split your cam and valve train setup? I only need one
Forum: Swap Shop
12-01-2020, 07:31 AM
Replies: 12
Views: 9,481
Posted By Tahoe540

If you just post the drive you might get some...

If you just post the drive you might get some interest. I looked awhile for a spare before I found one for my old boat.

Not many out there. I think I ended up buying and selling that spare for...
Forum: Swap Shop
11-15-2020, 07:48 AM
Replies: 7
Views: 1,791
Posted By Tahoe540

Are these step nose/Gen VI

Are these step nose/Gen VI
Showing results 1 to 25 of 309
 
Page 1 of 13
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.